• Heat Fab 4526SS Saf-T Vent 5" Diameter - 304 Storm Collar

    Storm Collar -For use with the Tall Cone Flashing (sold separately) or other roof flashings to provide support to vertical installations. The storm collar may be tightened and sealed around the vent to prevent water from entering the building. It may also be used as a decorative shield to cover holes where the vent penetrates interior concrete and masonry walls. This part is made from Type 304 stainless steel and should not be installed in the direct path of flue gases.

    • Brand: Heat Fab
    • ASIN: B00562KZFM
    • UPC: 711884506372

  • Heat Fab SC03ADEZ Saf-T Vent SC 3"/5" Concentric Adapter from EZ Seal

    Heat Fab SC03ADEZ Saf-T Vent SC 3"/5" Concentric Adapter from EZ. Single Wall Adapter/Appliance Adapter - Use to transition from single-wall to Saf-T Vent SC. The male end connects to Saf-T Vent EZ Seal or Saf-T Vent appliance adapters and flue collars. The outer diameter collar is vented and must not be blocked during installation or operation.

    • Brand: Heat Fab
    • ASIN: B002NQLTS6
    • UPC: 711884552904

  • Heat Fab 9405 Saf-T Vent EZ Seal - 4 Inch Diameter - 24" Straight Length

    24" Length- Install vent with a continuous pitch of 1/4'' per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system. Support horizontal portions of the vent system at 6-foot intervals. Vertical sections should be supported at least every 30-feet and after every offset or transition.

    • Brand: Heat Fab
    • ASIN: B00562K4NA
    • UPC: 711884556698

  • Heat Fab SC03RC Saf-T Vent 3" Diameter - Rain Cap, Category III & IV Only

    Rain Cap - Use as a termination on vertical systems. Category I and II appliances require a raincap or other device to prevent rainwater from entering the vent. Vent systems for positive pressure appliances may omit the raincap if there are other provisions for draining rainwater from the system. The raincap may also be used as a horizontal termination.

    • Brand: Heat Fab
    • ASIN: B00562LJ20
    • UPC: 711884525229

  • Heat Fab SC03HT Saf-T Vent SC 3"/5" Horizontal Termination Adapter

    Horizontal Termination Adapter- Use to complete the Saf-T Vent SC system after penetrating an exterior wall. Standard Saf-T Vent terminations connect directly to the adapter. The screened openings release excess heat from the system and must not be blocked. On Sealed Combustion systems the screened openings supply combustion air to the appliance.

    • Brand: Heat Fab
    • ASIN: B002NQLU8K
    • UPC: 711884552935

  • Heat Fab 9301PVC Saf-T Vent EZ Seal - 3" PVC Adapter

    Heat Fab 9301PVC Saf-T Vent EZ Seal - 3" PVC Adapter

    • Brand: Heat Fab
    • ASIN: B00D23MR3U
    • UPC: 711884503487

  • Heat Fab SC03L6 Saf-T Vent SC 3"/5" Diameter - 6" Straight Length

    Heat Fab SC03L6 Saf-T Vent SC 3"/5" Diameter - 6" Straight Length. Install vent with a continuous pitch of 1/4" per foot, sloping upward toward the termination (unless otherwise specified by theappliance manufacturer).

    • Brand: Heat Fab
    • ASIN: B002NQSS0S
    • UPC: 711884579901

  • Heat Fab SC04HT Saf-T Vent SC 4"/7" Horizontal Termination Adapter

    4" Horizontal Termination Adapter For more than 15 years, Heatfab’s Saf-T Vent systems have been the leading superferritic stainless steel special gas vent. We were the first U.S. vent manufacturer to Test and List to UL 1738 (Special Gas Vent systems) using AL 29-4C®.Working closely with equipment manufacturers, our engineering department provides expertise to ensure your installation has high-performance quality from appliance adapter to termination. Saf-T Vent SC provides more than just a laser-welded double-wall system made from the toughest alloys. It also supports concentric venting, exhausting flue gases through the inner conduit while intaking combustion air through the outer jacket. The combined flue exhaust/combustion air intake eliminates the need for two separate penetrations through the wall or roof. Cut only one installation hole, install necessary hangers once, install one termination/air intake. Zero-clearance installations in stud walls or floor spaces. Concentric venting speeds installation with exhaust and intake through one vent. Constructed of AL 29-4C® with built-in seal.

    • Brand: Heat Fab
    • ASIN: B00562KNW2
    • UPC: 711884544190

  • Heat Fab SC04VSL Saf-T Vent SC 4"/7" Diameter - Vertical Support Leg

    Heat Fab SC04VSL Saf-T Vent SC 4"/7" Diameter - Vertical Support Leg. Vertical Support Leg - For use on vertical systems to provide support. The 20-gauge stainless steel support legs can be used below or above the roof, and can be used in pairs for extra stabilization. Hardware to attach the support to the structure is not provided; attach using best construction methods. Be sure to consider clearances when planning the system. Never drill or screw through the Saf-T Vent SC inner vent conduit.

    • Brand: Heat Fab
    • ASIN: B00562Q70E
    • UPC: 711884544350

  • Heat Fab 9302 Saf-T Vent EZ Seal - 3 Inch Diameter - 12" Straight Length

    12" Length- Install vent with a continuous pitch of 1/4'' per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system. Support horizontal portions of the vent system at 6-foot intervals. Vertical sections should be supported at least every 30-feet and after every offset or transition.

    • Brand: Heat Fab
    • ASIN: B00562K2BO
    • UPC: 711884552560

  • Heat Fab 9414 Saf-T Vent EZ Seal - 4 Inch Diameter - 90° Elbow

    90° Elbow- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 10 feet of vent for 3 and 4 inch diameters.

    • Brand: Heat Fab
    • ASIN: B00562KKXO
    • UPC: 711884556759

  • Heat Fab 9308 Saf-T Vent EZ Seal - 3 Inch Diameter - 48" Straight Length

    48" Length- Install vent with a continuous pitch of 1/4'' per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system. Support horizontal portions of the vent system at 6-foot intervals. Vertical sections should be supported at least every 30-feet and after every offset or transition.

    • Brand: Heat Fab
    • ASIN: B00562K688
    • UPC: 711884553666

  • Heat Fab 9314 Saf-T Vent EZ Seal - 3 Inch Diameter - 90° Elbow

    90° Elbow- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 10 feet of vent for 3 and 4 inch diameters.

    • Brand: Heat Fab
    • ASIN: B00562KK5C
    • UPC: 711884555592

  • Heat Fab 9305 Saf-T Vent EZ Seal - 3 Inch Diameter - 24" Straight Length

    24" Length- Install vent with a continuous pitch of 1/4'' per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system. Support horizontal portions of the vent system at 6-foot intervals. Vertical sections should be supported at least every 30-feet and after every offset or transition.

    • Brand: Heat Fab
    • ASIN: B00562K4XA
    • UPC: 711884552584

  • Heat Fab SC03AD01E Saf-T Vent SC 3"/5" Concentric Rinnai 90 Degree Elbow

    The elbow adapter, SC3AD01E, is specially designed to connect directly into the vent outlet of the Rinnai Continuum model V2532.

    • Brand: Heat Fab
    • ASIN: B002NQLTOU
    • UPC: 711884579819

  • Heat Fab SC04FSA Saf-T Vent SC 4"/7" Diameter - 12x12 Firestop-Support-Wall Plate

    Heat Fab SC04FSA Saf-T Vent SC 4"/7" Diameter - 12x12 Firestop-Support-Wall Plate. Fire Stop / Support / Wall Plate- A fire stop may be required anytime Saf-T Vent SC penetrates combustible floors, walls, or ceilings. Remove any insulating material from the floor, wall, or ceiling cavity for at least 1 inch around the vent. Review fire codes and consult with local building code officials to determine the necessity for a firestop. This part provides added support when used at the bottom of a vertical chase. Hardware is supplied to attach the firestop to the vent. Mounting hardware is not provided.

    • Brand: Heat Fab
    • ASIN: B0043ACSIA
    • UPC: 711884544275

  • Heat Fab 9309 Saf-T Vent EZ Seal - 3 Inch Diameter - 15° Elbow

    15° Elbow- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 3 feet of vent.

    • Brand: Heat Fab
    • ASIN: B00562KDHC
    • UPC: 711884557497

  • Heat Fab SC03E90 Saf-T Vent SC 3"/5" Diameter - 90° Elbow

    Heat Fab SC03E90 Saf-T Vent SC 3"/5" Diameter - 90° Elbow. Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable.

    • Brand: Heat Fab
    • ASIN: B002NQRDEU
    • UPC: 711884552874

  • Heat Fab 9314TERM Saf-T Vent EZ Seal - 3" 90 Degree Screen Elbow Termination

    Elbow Termination with Screen - Use as a termination on horizontal or vertical systems, as specified or allowed by the appliance manufacturer.

    • Brand: Heat Fab
    • ASIN: B00562KA3Y
    • UPC: 711884567502

  • Heat Fab SC04L36 Saf-T Vent SC 4"/7" Diameter - 36" Straight Length

    Heat Fab SC04L36 Saf-T Vent SC 4"/7" Diameter - 36" Straight Length. Install vent with a continuous pitch of 1/4" per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer).

    • Brand: Heat Fab
    • ASIN: B002NQSS3A
    • UPC: 711884544299